重庆理工大学
材料成形CAE报告
课程名称 材料成形CAE
姓 名 × × ×
班 级 × × ×
学 号 × × ×
日 期 × × ×
2011 年11月
实验课程名称: 材料成形CAE
第二篇:CAE实验报告
CAE上机实验报告
专业:08热动1班
学号:0845521115
姓名:高森
日期:20##-12-10
指导老师:张 建
目 录
一 问题表述
二 有限元建摸
三 结果分析
四 总结
实验报告
一 问题描述
对象:悬臂梁
尺寸:60*30*5 mm
材料:45钢,弹性模量为210Gpa,泊松比0.3
边界:一端固定,另一端施加21115N
要求:求出位移和应力
二 有限元建摸
图1
三 结果分析
图2
由图可见,在Mesh模块进行网格划分,为与图1进行对比,参数设置均一致,悬臂梁的右上角截面处受到力F=2.12e+04N,网格划分后模型如图所示。
图3 位移结果
由图可见,在ANSYS分析的结果中,我们可以看出从蓝到红变形量逐渐增大,且在臂端变形量集中达到最大,向固定端一侧位移变量渐渐变小,截面处为最大位移v=8.42e-01m,悬臂梁的左端为最小位移=0.00e+00m,即位移为零。这与弹性力学中所求的解析吻合,同时应用软件得出的结果也是正确的。说明此实验用ANSYS分析的结果是正确的。
图4 Vcn Mises结果
由图可见:颜色从蓝到红,应力逐渐变大。当鼠标指向节点时,能显示此节点的冯米斯应力值。应力大部分集中在固定端,且在固定端两端点处应力值达到最大。由左上方悬臂梁左上,下端应力为应力最大处,其最大应力=9.97e+02Mpa,悬臂梁的右下端为应力最小处,其最小应力=1.25e+02Mpa
图5 最大主应力结果
由图可见:悬臂梁的左上,下端为主应力最大处,其最大主应力=1.05e+03Mpa;悬臂梁的右下端为主应力最小处,其最小应力=1.20e+02Mpa。
四 总结
操作过程:
1.Create a material and a property,and set all the needed dates such as card-imagine、color 、nodes.
2.Create 2 components,and input the dates.
3.Click the spline and select the botton mesh keep surf in the item 2D.
5.click shift+f2 to clear all the nodes.
6.Load 2 collectors one named as spc and the other as loa.
7.Select the constraint and shift + leftclick or rightclick to choose the points of the object in the item analysis.And then click "o" on the keyboard to set graphics size=4.
8.Set my school number 21115 as the force in the analysis.Create a y-axis and ctrl+mid-click to adjust the object's size.And then set load types =force
9.Click the button component to copy the first 2 graphic jpgs.
10.Select radioss in the analysis.Save and radioss.
11.Click the post and contour to print the third graphic jpg.And select change the date types as vom mises for the fourth graphic jpg,and maximum contour for the fifth graphic jpg.That's all the progresses.
通过这16个学时的上级实验,在老师的讲解以及自己的实际操作下,我对CAE建模又了更深一步的认识,基本掌握了将实际问题转化为CAE基本问题,然后针对工程实际进行有限元建模的分析方法。在整个上机实验中,从听取老师的讲解,到一步一步学习,再到自己看着工程实例步骤练习,基本上能够做到独立进行有限元的分析,系统求解,生成结果。同时在老师的讲解之下,也知道了不少在CAE软件运用中的快捷方式,这对于以后的实际工作都有不少帮助。