1 / 8
检 验 报 告
TEST REPORT
NAME OF SAMPLE: 汽车铝合金车轮
CLIENT:
CLASSIFICATION OF TEST: SGS审核检验
芜湖宝德轮业有限公司实验室
中国安徽省芜湖市机械工业园区工业大道纬五路.241000
Weiwu Road,Industry Av,Machinery Industrial Zone Wuhu City,Anhui Province,China.241000 Wuhu Pilotdoer Wheel Co., Ltd.Laboratory
2 / 8
芜湖宝德轮业有限公司
检 验 报 告
TEST REPORT
Approved by: Reviewed by: Tested by:
3 / 8
芜湖宝德轮业有限公司
检 验 报 告
TEST REPORT
4 / 8
In accordance
with the
1641N.M load
Bending moment M=1641N.M, rotating at 180000 rpm.
1 wheel can continue to bear the load; rotating at 180000 RPM after 1 wheel can In accordance with the 1641N.M load rotating at 180000 RPM after 1 wheel can
Light load continue to bear continue to bear dynamic the load; the load; 2 wheels of any part can not 2 bending fatigue appear new visible crack ( by dye ( sample fluorescent inspection ); recognition 3, 4) penetration method or the 2 used by dye penetration
inspection did
visible crack; 2 used by dye penetration inspection did visible crack; P 3 to meet the requirements of the
cycle number, loading point offset is not allowed to exceed the initial load offset 20% not appear new not appear new 3 cycles prior to 3 cycles prior to
offset for the offset for the
1.52 initial value 0.94 initial value of 1.74 offset < of 1.32 offset < 20%
In accordance
with the
2462N.M load
rotating at
200000 RPM
after
1 wheel can 20% In accordance with the 2462N.M load rotating at 200000 RPM after 1 wheel can
the load;
2 used by dye
penetration
inspection did
visible crack;
3.Achieve the
cycle number
1.68, the initial
value of 1.73
offset < 20% Bending moment M=2462N.M, rotating at 200000 rpm. 1 wheel can continue to bear the load; Heavy duty the load; dynamic 2 wheels of any part can not 3 bending fatigue appear new visible crack ( by dye 2 used by dye penetration method or the continue to bear continue to bear P ( sample fluorescent inspection ); recognition 5, 6) penetration inspection did not appear new not appear new 3 to meet the requirements of the visible crack; cycle number, loading point offset is not allowed to exceed the initial load offset 20% 3.Achieve the cycle number 1.60, the initial value of 1.64 offset < 20% before offset is before offset is
5 / 8
6 / 8
7 / 8
8 / 8
注意事项
Important
1. 报告无检验单位公章无效；
The report without inspection unlt is invalid;
2. 未经本试验室书面同意，不得部分地复制本报告；
Without the written consent of test chamber, is not allowed to be copied this report;
3. 报告无主检、审核、批准人签名无效；
The test report is invalid without the signatures of Author and Reviewer;
4. 报告涂改无效；
The test report is invalid if altered;
5. 对检验报告若有异议，请于收到报告之日起十五天内向检验单位提出；
Any questions on the report, please to receive the report within fifteen days of the date of inspection unit;
6. 一般情况，委托检验结果仅对所检验样品有效；
Generally, commission test is responsible for the tested samples only;
7. 检验结果中“N”表示“不适用”，“P”表示“通过”，”F”表示”不通过”。
As for the test result, “N” means “not applicable”, “P” means “pass” and “F” means “fail”.
地 址：中国安徽省芜湖市机械工业园区工业大道纬五路.241000
Address: Weiwu Road,Industry Av,Machinery Industrial Zone Wuhu City,Anhui
Province,China
电 话(Tel)：086-0553-8128251
传 真(Fax)：086-0553-8128133
邮政编码(Post Code)：241000
E-mail：yangjixiang112@126.com
第二篇：mathematica,matlab实验报告
实验报告
序号 成绩 姓名 班级 学号
一、实验题目
二、实验目的和要求
三、实验所用软件及版本
四、实验过程记录（基本步骤、主要程序清单、异常情况记录等）
第1页 / 共2页
五、实验结果
六、思考与总结
第2页 / 共2页